Webserver using NETMF and Gadgeteer December 13, 2013

7 minute read

Hi there, today we will tackle the task to host a little web server on a micro controller that runs the .NET Microframework and expose some REST like endpoints.

Stuff and things

  • FEZ Cerberus or FEZ Hydra or FEZ Spider
  • Power module
  • ENC 28 module
  • 2x Gadgeteer cable
  • Mini USB cable


If you want to use a FEZ Spider board, we already have an article for this preparation step. After that you can directly jump to the implementation part.

Depending on your micro controller board you have to do some prior steps before we can switch to implementing. Since I will use the FEZ Cerberus the preparations described here are explicit to that board. I also tested it with the FEZ Hydra board and it works even though GHI Electronics explicitly mention that it may harm the Hydra, in my case it worked as well as the Cerberus. But don’t make responsible if you fry your Hydra board.

Firmware update

To use the Cerberus with the ENC28 ethernet module you first need to flash a new firmware to the board. The development packages of GHI Electronics contain a tool called “FEZ Config” which is able to transfer the firmware. In the same packaged are also two firmwares for the Cerberus and the Hydra. One without Ethernet support and the other one includes it. I guess it’s obvious that you have to flash the one including the Ethernet support.

Mandatory Connection

After that GHI Electronics states that it is mandatory to connect the ENC28 module at all time to the board if you want to avoid damaging it. I forgot it several times by now and so far nothing happened, I guess their motto is: Safety first.

On the Cerberus board you need to connect the Ethernet module to socket 6. For other boards please check the GHI Electronics website for further information.

Open Source Mainboards

Before we can implement the ethernet connection I have to mention one exception of the open source mainboard from GHI electronics: Once you start up Visual Studio, create a new Gadgeteer project and drag the ethernet module into the Visual Designer you get an error message. Well don’t be frustrated and skip the step, you don’t need it, if you have flashed the Ethernet firmware to the board, the ENC28 module is basically hardwired to the micro controller board. Just use it!


The following source code will initialize the ethernet module and is originally GHI Electronics and available on their Codeshare page. I just added some debug lines to output the acquired IP address and so on. GHI Electronics again state, that the code will only work on the Cerberus and not the Hydra. Well what can I say, I tested it and it just works.

private string InitNetwork()
    Debug.Print("Initializing network...");
    string ipAddress = string.Empty;
    NetworkInterface[] interfaces = NetworkInterface.GetAllNetworkInterfaces();
    if (interfaces != null && interfaces.Length > 0)
        NetworkInterface networkInterface = interfaces[0];
        Boolean isDhcpWorked = false;
        // dynamic IP address
        if (networkInterface.IsDhcpEnabled == false) 

        // Wait for DHCP (on LWIP devices)
        for (int i = 0; i < 5; i++)
            networkInterface = NetworkInterface.GetAllNetworkInterfaces()[0];
            if (networkInterface.IPAddress != "")
                isDhcpWorked = true;
            Debug.Print("Waiting for an IP Address...");
        if (Microsoft.SPOT.Hardware.SystemInfo.SystemID.SKU != 3)
            if (isDhcpWorked == false)
                // static IP address

                networkInterface.EnableStaticDns(new[] { "" });
                string h = "df";
                Debug.Print("DHCP not enabled.");
        ipAddress = networkInterface.IPAddress;
        Debug.Print("Network ready.");
        Debug.Print("  IP Address: " + networkInterface.IPAddress);
        Debug.Print("  Subnet Mask: " + networkInterface.SubnetMask);
        Debug.Print("  Default Getway: " + networkInterface.GatewayAddress);
        Debug.Print("  DNS Server: " + networkInterface.DnsAddresses[0]);
        Debug.Print("No network device found.");
    return ipAddress;

Web Server

After running the code on the board, the output window of Visual Studio will show the above infos and the ethernet connection is ready. Next step is the web server. For that you need a new reference in you Gadgeteer project. Navigate to the Add Reference windows, scroll to the bottom and select the Gadgeteer.WebServer library.

The important class inside the library is called WebServer and exposes two methods which will help us setup the web server.

  1. StartLocalServer
  2. SetupWebEvent

The first one StartLocalServer allows the initialization of the server. You just pass the returned IP address from the network init method as a first argument and the desired port as the second argument. That’s it. Done!

Execute the project on your FEZ board, navigate to the IP and port in your browser and voilá, your web server is up and running.

WebServer.StartLocalServer(ipAddress, 80);

Web Events

Finally, we’re done with setting things up and can start with the fun part, registering WebEvents. This is done with the second of the above methods – SetupWebEvent(). The constructors takes one string argument which will determine the path of the URL. For example if we pass the argument “example” into the constructor the resulting URL for this WebEvent will be http://IP:PORT/PATH. Now you can subscribe to the WebEventReceived event of the WebEvent object. The callback method now gets called every time when a HTTP message arrives.

WebEvent messageEvent = WebServer.SetupWebEvent("message");
messageEvent.WebEventReceived += MessageEventOnWebEventReceived;

Within the callback method we can access the URL parameters and respond to the sender of the message. The following code will show an example of how to do exactly that.

private void MessageEventOnWebEventReceived(
    string path, 
    WebServer.HttpMethod method, 
    Responder responder) 
    string text = responder.UrlParameter['text'].ToString();
    responder.Respond("Deine Nachricht " + text + " wurde empfangen.");

If we now call the following URL in the browser: http://IP:PORT/message?text=Yeah

We get this result. So far so good, now you know how to setup a REST like web server on a GHI Electronics Gadgeteer board.

On the same Codeshare page as mentioned in the beginning of this article you can also find a JSON library to serialize and deserialize your data to send it over the wire… unless you want to go full binary.